This post provides you a reference design to start building your barn door tracker. You might want to refer to the other posts in this blog for detailed design choices. The design is for an “isosceles” barn door tracker. This design’s fundamental idea is to use readily available components in the market and to give an opportunity for people with minimal DIY skills to build it.
The bill of materials to build the tracker
Please note that you can exchange some of the components listed below to what is easily available for you. The choice of the 8mm pitch lead screw was made because this is available in high quality and at very low prices thanks to the popularity of DIY 3D printing machines. This lead screw (threaded rod) is used extensively in the build of 3D printing machines. If you change this, then corresponding change needs to be done in the software side to change the motor speed. If you are using your own motor speed controller, then take a look at the online speed calculator.
|Ply wood for camera arm and fixed arm||350mm x 200mm||2|
|Ply wood for motor and nut carriers||80mm x 100mm||2|
|Door hinges||76mm (3")||6|
|Threaded rod or lead screw||200mm length, 8mm pitch, trapezoidal thread (Standard for DIY 3D printing machines and hence widely available)||1|
|Nut for threaded rod or lead screw||To suit your selection of threaded rod||1|
|Shaft coupler||8mm to 5mm (or to match your selection of threaded rod and stepper motor shaft)||1|
|Stepper motor||NEMA 17 bipolar stepper motor||1|
|Stepper motor mounting bracket||To suit your motor. Flat.||1|
|Control circuit||Reference circuit||1|
|Ball head for camera mounting||Mini ball head for lenses up to 55mm. Heavier lenses will requires good ball heads||1|
|Laser pointer||Green laser pointer for polar alignment||1|
Mechanical plan for the tracker
The following plan is can be viewed in full size by clicking on the image. Let’s do a quick run of the design:
- The primary hinges connect the camera arm and the fixed arm like a “barn door”. That’s why this is called a barn door tracker
- The other hinge pairs have the following uses
- 1 pair connects the nut carrier to the camera arm
- 1 pair connects the motor carrier to the fixed arm
- These hinges provide the freedom for the carrier plates to automatically adjust their position as the two arms spread away from each other. This is a critical part of the design. The rigid threaded rod connected to both the carrier plates will force the hinges to adjust themselves to create the “isosceles” triangle
- Note the dark gray color in the hinge mounting holes. Only these positions have to be screwed. The blank holes should be left without fastening with screws. This configuration gives the hinges the required freedom to allows them to automatically adjust.
- The position of the ball head should be as close to the primary hinges as possible. This reduces the load on the stepper motor, allowing heavier lenses to be used.
- The shoulder for the laser pointer can be anywhere, but needs to be as parallel as possible to the primary hinges. We use the laser pointer to do polar alignment. Polar alignment in the case of a barn door tracker is making the hinges point to the north celestial pole (pole star for practical reasons)
The electrical circuit
The barn door tracker has been around since 1975. This was a time in which access to electronics and micro-controllers would have been limited to specialized engineers and labs. Today the prolific proliferation and commodification of micro-controllers puts in the hand of the average DIY enthusiast. Especially systems like the Arduino make it very simple to code and download your software into micro-controllers. In our use case, the Arduino micro-controller is used for the following:
- User interface – Buttons to control tracking, pause, rewind and fast-forward
- Speed control of the stepper motor.
- Home position detection
- Mode selection – 300mm / 400mm arms, 8mm pitch / 1.5mm pitch
The other important component is the stepper motor controller. We choose to use a DRV8255 based controller. The DRV8255 manufactured by Texas Instruments is a integrated stepper motor controller. There are many DRV8255 carrier boards available. Most of them are pin compatible with each other. The breakout boards for TI’s DRV8825 micro-stepping bipolar stepper motor controllers feature adjustable current limiting, and six micro-stepping resolutions (1 step to 1/32-step). We choose to use 1/32 micro-stepping mode in our design.
The two most expensive components of this circuit are the Arduino (~$8) and the DRV8255 breakout board (~$5). Arduino clones are available for even lower prices.
The circuit requires a 12V DC power source capable of providing 1 amp current. The
I/O details of the circuit:
|12V SUPPLY||12V 1A external power supply||A NEMA 17 stepper motor will typically consume around 400 mA of power|
|TRACK||Push button or keypad||Button user presses to start tracking|
|PAUSE||Push button or keypad||Button user presses to pause tracking|
|F>FWD||Push button or keypad||Button user presses to wind the mount in the tracking direction|
|REWIND||Push button or keypad||Button user presses to wind the mount in the reverse direction|
|HOME||Limit switch or button||Limit switch placed in such a way that it signals the home (bottom most position of camera arm) to the controller. There is an overriding push button in case limit switch cannot be provided|
|COIL 1/A||Stepper motor coil #1|
|COIL 1/B||Stepper motor coil #1|
|COIL 2/A||Stepper motor coil #2|
|COIL 2/B||Stepper motor coil #2|
If you want a fully built circuit, you can buy it from me. Please get in touch. More information is here. This is an Arduino shield. You will have to plug it in on top of an Arduino.
The source code for the smart barn door tracker is posted below. This source code is to compiled and downloaded to the Arduino. This source code is fairly well documented if you need to make any changes of your own to suit your barn door tracker.
Reference build image gallery
Astro photography made with this mount